AISI S200-07 PDF

editions of the Specification developed by AISI and CSA. AISI: for example, this Specification will be referred as AISI S, where the last. AISI SSERIES FRAMING STANDARDS BUNDLE. This bundle includes 11 documents. (Download). AISI S/S (). AISI S AISI. AISI-S General requirements for residential and commercial construction, prescriptive and engineered design. Examples include member identification.

Author: Maumi Teramar
Country: Reunion
Language: English (Spanish)
Genre: Personal Growth
Published (Last): 14 June 2010
Pages: 153
PDF File Size: 14.87 Mb
ePub File Size: 2.76 Mb
ISBN: 544-5-15564-235-2
Downloads: 49076
Price: Free* [*Free Regsitration Required]
Uploader: Kagalabar

The truss component structural performance load test and full-scale truss confirmatory test methods, previously included in AISI S, are provided in this appendix.

It outlines the scope, which is for design and installation of cold-formed steel framing of a floor and roof systems, b structural walls, c shear walls, strap braced walls, and diaphragms to resist in-plane lateral loads, and d trusses for load-carrying purposes in buildings. This has been an often asked question by framing design engineers. The effective strip method is permitted to be used within the following range of parameters:.

For curtain wall systems, the standard now permits the use of the bracing combination of sheathing attached to one side of the wall stud and discrete bracing for the other flange Figure 1.

Industry News

Section reference table S and previous standard. This article focuses on AISI S which applies to cold-formed steel structural members subject to gravity loading, wind loading, and seismic loading, except when specific seismic detailing is required. From tothe AISI Committee on Framing Standards developed nine different framing standards to cover specific aspects of cold-formed steel aisl.

This limitation has been eliminated from AISI S; however, it should be remembered that mils is still the maximum thickness of standard products in the United States and 97 mils 0.

This new exception provides for a more economical built-up member, as is often used as a jamb stud or shear wall boundary member. The discrete braces are limited to s200-7 greater than 8 feet 2.


These cold-formed steel framing standards are available as free downloads at www. This chapter contains design, manufacturing quality criteria, and installation requirements for cold-formed steel trusses as previously included in AISI S Effective strip method model for steel-sheet sheathing.

This method provides an alternative approach to determine the shear wall strength, especially for those aii are outside the limitations of the tested systems. Six of aiis standards addressed the design of structural elements, such as general provisions, wall studs, floor joists, trusses, headers, and shear walls. The exception applies where the built-up section is seated properly in a track, and the top and bottom end bearing detail of the studs consists of a steel or concrete support with adequate strength and stiffness to preclude relative end slip of the two built-up stud sections.

But, why would AISI develop six discrete framing standards as opposed to one design manual? Wisi, for ease of use, S contains a section reference table between the S provisions and the previous provisions Table 2.

AISI Cold-Formed Steel Standards Offered As Free Downloads

Beneficial for the design engineer is a new Effective Strip Method that enables the calculation of the nominal in-plane shear wall strength for Type I shear walls Figure 2. This chapter provides installation requirements previously contained in the various framing standards.

However, AISI S now incorporates an exception for a built-up axial load bearing section comprised of two aisj oriented back-to-back forming an I-shaped cross-section. The s200-077 design standards limited their application to framing members having a maximum base steel thickness to mils 0. The use of ASTM E results in higher nominal shear strength values as compared with the cantilever test method historically used for steel deck diaphragms.

This new standard includes design provisions for wall systems, floor and s200-077 systems, lateral force-resisting systems, as well as truss and header assemblies.


For roof or floor diaphragms with a maximum aspect ratio of 4: Inthe manufacturing tolerance values were extended to the flange width and stiffening lip length.

This newly developed chapter provides minimum requirements for quality control and quality assurance for material control and installation for cold-formed steel light-frame construction.

Leave a Comment Click here to cancel reply. This appendix contains requirements for the determination of the rotational ausi that structural sheathing provides to framing members to facilitate the design for distortional buckling.

Cold-Formed Steel: SCREWS Self-Drilling Fasteners

Format defines design considerations. Sheathing and discrete bracing. This new chapter lists applicable AISI test standards for cold-formed steel framing members, connections, and systems.

ASTM S200–07 has historically stipulated manufacturing tolerances for cold-formed steel structural framing members. The simple reason is, it was easier to develop small single-topic documents versus a more comprehensive multi-topic document. This chapter contains design provisions for cold-formed steel framing members and assemblies, as previously included in AISI S, S, S, and S First Name Last Name.

Free CFS Publications from the AISI/SMDI Construction Market Council

This computational method is applicable for walls sheathed with steel sheet. The ends of a built-up compression member are connected by a weld having a length not less than the maximum width of the member or by connectors spaced longitudinally not more than 4 diameters apart for a distance equal to 1.

The method assumes a sheathing strip carries the lateral load via tension field action. The other standards addressed such topics as a code of standard practice, the definition of standard product, and prescriptive design for residential applications. Your message Submit Comment. The chapter also includes:.