ASTM B221-08 PDF

Buy Metal Online – Online Metal Store – Order Large or Small Quantity ASTM B T6 Aluminum Equal Leg Structural Angle – Cut to Size Structural. Buy Metal Online – ASTM B T6 Aluminum Round Tube – Order Large or Small Quantity Online – Cut to Size Aluminum Round Tube – No Minimum. Jiangsu Haohua Industry Group as one of the leading suppliers in China to supply ASTM B T6 Aluminum Pipe etc. [Contact person:Ms chris ; Email.

Author: Gugami Bralrajas
Country: Liberia
Language: English (Spanish)
Genre: Literature
Published (Last): 28 December 2013
Pages: 471
PDF File Size: 8.7 Mb
ePub File Size: 3.56 Mb
ISBN: 277-8-84665-632-6
Downloads: 5833
Price: Free* [*Free Regsitration Required]
Uploader: Sall

The cladding composition is more b221–08 to determine because of the relatively thin layer and because of diffusion of core elements to the cladding. Wire, Rod, Bar and Pro?

L Only in tube form. The producer may analyze samples for trace elements not speci? As much of the rejected material as possible shall be returned to the producer or supplier by the purchaser.

C For the purpose of determining conformance to these limits, bb221-08 observed value or a calculated value obtained from analysis shall be rounded to the nearest unit in the last right-hand place of the?

Each sample shall be taken from material considered acceptable in accordance with the lot-acceptance criteria of Table 4. Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters.


ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard.

F The aluminum content shall be calculated by subtracting from All specimens so selected for retest shall meet the requirements of the speci? NOTE 3—It is standard practice in the United States 2b21-08 industry to determine conformance to the chemical composition limits prior to further processing of ingots into wrought products.

If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below.

ASTM B PDF – $ : : National Standards Institute Documents Download Store

Other methods may be used only when no published ASTM test method is available. A superscript epsilon e indicates an editorial change since the last revision or reapproval. M Composition of cladding alloy applied during the course of manufacture.

Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may atm. In case of dispute, the methods of analysis shall be agreed upon between the producer and purchaser.

X, and so forth A2. The applicable level shall be as speci? Marking for shipment of such material shall be in accordance with Fed.

ASTM B221-08 6061-T6 Aluminum Bar Steel Round Bars / Tubes For Stakes , Tines

Materials and Manufacture 5. K Yield strength is not applicable in tube. B The thickness of any element of a pro?

B — 05a Standard Speci? Sampling shall be in accordance with Practice E T62G 5 H up through 25 over 25 through 32 up through 32 2.


C The discontinuity class limits are de? Elongation of cut-out round specimens is measured in zstm specimen diameter. C Elongation of full-section and cut-out sheet-type specimens is measured in 2 in. The electrical b2221-08 shall be determined in accordance with Practice B21-08 in the following locations: Heat Treatment and Reheat-Treatment Capability NOTE 2—For rolled or cold-?

Should any analysis by the producer or the purchaser establish that an Others element exceeds the limit of Each or that the aggregate of several Others elements exceeds the limit of Total, the material shall be considered nonconforming. K Bismuth and lead shall be 0. However, should subsequent testing by the purchaser establish that the material does not meet these requirements, the material shall be subject to rejection.


I Minimum yield strength for tube, Analysis shall be made for the elements for which limits are shown in this table. I Aztm plus chromium shall total 0. The total for other elements does not include zirconium.

A minimum of three adjacent replicate specimens shall be taken from each sample and tested. This standard has been approved for use by agencies of the Department of Defense.