ASTM D3276 07 PDF

Designation: D – 07Standard Guide for Painting Inspectors (Metal Substrates)1 This. Buy ASTM D GUIDE FOR PAINTING INSPECTORS (METAL SUBSTRATES) from SAI Global. ASTM D – Designation: D – 00 Standard Guide for Painting Inspectors (Metal Substrates.

Author: Kagajin Yozshulmaran
Country: Mexico
Language: English (Spanish)
Genre: Medical
Published (Last): 8 September 2013
Pages: 126
PDF File Size: 20.9 Mb
ePub File Size: 19.82 Mb
ISBN: 697-9-69809-515-6
Downloads: 37043
Price: Free* [*Free Regsitration Required]
Uploader: Nikojas

ASTM D e1. A number in parentheses indicates the year of last reapproval. A superscript epsilon e indicates an editorial change since the last revision or reapproval. It includes the key elements of surface preparation, coatings application, and? The items should be selected that are pertinent to the speci? NOTE 1—For additional helpful information, refer to the following documents: Available from Materials manufacturer.

See Guide D for establishing procedures to certify inspectors for coatings work in nuclear facilities. The values given in parentheses are for information only. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Current edition approved June 10, Originally published as D — Last previous edition D — Many of the details covered may be in a speci? A checklist for use in the? Preparation for Inspection 4. Government Printing Office, Washington, D. The inspector should examine these materials and be supplied with appropriate protective equipment and devices. Surface Preparation Methods and Requirements 5. The standard is used by the inspector to assist in determining whether the degree of surface preparation speci?

For large jobs it is recommended that before work starts, an actual steel sample of adequate size be blasted to the satisfaction of the project engineer.

ASTM D3276:15

This blasted surface should astmm protected by a clear acrylic coating or encased in plastic and used for reference purposes as the work progresses. These include oil, grease, soil, weld spatter, and slag, that make it impossible to obtain proper adhesion to the metal surface. Deposits of salt such as chlorides and sulfates should be removed, or longterm coating performance will be seriously affected. SSPC issues detailed surface preparation speci?

This scale is very brittle and can crack or loosen due to temperature changes both in fabricating and weathering in the? Coarser abrasives generally produce a coarser and deeper pro? A general recommendation is that the surface pro? Xstm recommendation does not apply if the resulting pro? The angularity sharpness and density of the pro? Methods for measuring surface pro? Each has its own safety-related hazards, and U. Occupational Health and Safety Administration regulations should be followed.

Materials Safety Data Sheets MSDS for the solvents and cleaning compounds provided by the manufacturer should also be consulted for proper worker protection. The solvent is applied to the surface by wiping or scrubbing with rags or brushes.

The contaminants should be removed not simply sstm out by a thorough wiping of the affected areas with cloths saturated with clean solvent. Contaminated cloths should not be dipped into clean solvent. The cleaning should be repeated with clean rags and fresh clean solvent. Emulsions, cleaning compounds, steam cleaning, or similar methods and materials may also be used. Where emulsion cleaners, soaps, or detergents are used, they should be removed completely by washing with clean hot water.


Vapor cleaning removes all soluble contaminants but does not disturb the natural oxide? The part to be cleaned is placed in the saturated vapor above the heated solvent so that the solvent vapor condenses on the metal surface.

ASTM D – 07 Standard Guide for Painting Inspectors (Metal Substrates)

Vapor degreasing does not remove particulate matter, so parts should be wiped to remove any insoluble soils. Vapor degreasing has the advantages over solvent wiping in that hot solvents are used sstm the solvent condensation removes oils without recontamination. Material is considered tightly adherent if it cannot be lifted with a dull putty knife. SSPC provides a detailed speci? D327 should be kept free of all materials that may clog the wires of the brush. Scrapers should be kept sharp at all times.

Hand tool cleaning in accordance with 5. All impact tools should be kept sharp. It also requires a minimum of 1-mil anchor ast Surface cleaning, power tools, and surface pro? Surface cleaning power tools consist of non-woven abrasive wheels and discs, coated abrasive discs or sanding pads, coated abrasive? All oil, grease, weld? Hand tool cleaning 5. Needle guns require 2-mm diameter needles to produce asrm suitable surface pro?

Slight residues of rust and paint may remain in the lower portions of pits if the original surface was pitted. SSPC-Vis 3 is a visual standard to assist in determining compliance.

Water may be injected into the air stream to control dust. In another method used primarily in fabricating shop, wheels propel the abrasive centrifugally against the work. The minimum and maximum particle size of the abrasive may be speci? Test the compressed air supply in accordance with Test Method D D2376 cleaning is often performed from the top to bottom of the structure and should only be carried on downwind from any recently zstm areas.

Dry blast cleaning operations should not be conducted on surfaces that will be wet after blasting and before painting.

The two sets of photographs are not directly comparable. C Pictorial Standard Sa 2 shows mill scale and con?

Surfaces that have been dry blasted should be brushed with clean brushes, blown with compressed air free of oil and moisture, or vacuum cleaned to eliminate any traces of blast products, dust, or dirt from the surface.

This also serves to remove abrasive from pockets and corners. Reblasting will be necessary on any surface if rust bloom forms before coating can be applied. Pressures over KPa 20 psi are needed to achieve adtm coating removal when using only water.

Pressurized water alone will not remove mill scale efficiently, or impart an anchor pro? Inhibitors may be added to the water to prevent?

The surface should be dried or allowed asttm dry before coating. All dust, dirt, oil, grease, moisture, soot, tar, or other contaminants should be removed from unpainted surfaces. Previously painted surfaces should be similarly cleaned of all foreign matter; all deteriorated coating should be removed as well.


Mortar or cement drippings from earlier repairs should be removed by mechanical or chemical means. Tree limbs or other growth obstructing the structure should be cut away to provide ready access. Blasting debris that accumulates on horizontal surfaces should be removed. Special attention should be placed on examining hard to reach areas, the back side of nuts and bolts, sides of members in close proximity to other members or walls, and undersides of members.

Alternatively, the s3276 may be allowed to weather a minimum of 6 months before cleaning and painting. Vapor degreasing or immersion in an alkaline or acid cleaning solution are commonly used in shop work. Lead pigmented primers should never be used over aluminum surfaces.

The minimum treatment for aluminum is Type B, Method 3 of Practices Dwhich describes the use of an alcoholic phosphoric acid cleaner. The cleaning of each section, bay, or part of the work should be entirely completed, inspected, and accepted before any coating is applied. The system of alternately cleaning and painting short sections by one workman is not good practice since this can lead to surface or intercoat contamination.

Washing may also be necessary between coats of paint. Chloride from deicing salts or a marine environment, and sulfate contamination from air pollution have been recognized wstm main factors in premature breakdown of existing coating systems.

High-pressure water blasting is often used to remove these contaminants. When the existing coating contains regulated heavy metals such as lead or chromium, or other regulated compounds such as organotin, special precautions and handling of debris may be necessary. On lead removal projects, inspectors should be familiar with OSHA requirements for their own health and safety.

If painting is done outside, the cleaned areas should receive the? When surface preparation and painting are carried on indoors, overnight delays between coating and painting may be permissible except on blastcleaned surfaces. Insofar as practicable, the steel should be stored to avoid the formation of waterholding pockets. If outdoor storage lasts for several months, the inspector should check the integrity of the coating from time to time and verify that de?

The length of time between shop priming and erection and subsequent topcoating should be kept to a minimum to avoid the problem of intercoat adhesion. If necessary to remove grime and oil substances, they can be wiped, steam cleaned, power washed with detergents or cleaned with solvents selected so as not to soften the?

Miscellaneous scratches and breaks asm the shop coat, including those occasioned by? Great care should be exercised to prevent trapping corrosive salts under or between coats. He should ensure that surfaces not in contact but that will be made inaccessible by assembly or erection, have received the full number of speci?