Advanced Melt Flow System. The 6MPCA is the most advanced digital model offered within the Ray-Ran range of melt flow index testers. The operating. Find the most up-to-date version of ASTM D at Engineering ASTM D(). Standard Test Method for Flow Rates for Poly(Vinyl Chloride) with Molecular Structural Implications. standard by ASTM.
|Published (Last):||2 November 2006|
|PDF File Size:||10.79 Mb|
|ePub File Size:||18.76 Mb|
|Price:||Free* [*Free Regsitration Required]|
ASTM D Flow Rates for Poly Vinyl Chloride – Instron
Bluehill LE for Basic Testing. This test is specific to the measurement of Melt Flow Rates MFR or MFI of poly vinyl chloride compounds while detecting and controlling various polymer instabilities associated with the flow rate.
This statement further de? If instability still occurs, particularly at high?
If the difference between the two specimens is greater than 0. It may be necessary to reshape the end of the cutoff tool to obtain the best results.
Originally published as D — The values given in parentheses are mathematical conversions to inch-pound units that are provided for information only and are not considered standard. Description Contact Us This test method is used for quality-control tests on PVC compounds that have a wide range of melt viscosities.
The sensitivity of this test method makes it useful for correlating with processing conditions and as an aid in predicting changes in processing. The sensitivity of the material to temperature necessitates slightly tighter controls than those stated in Test Method D NOTE 4—A positive instability probably indicates that crosslinking is occurring.
ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard. If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below. These changes are due to three types of measured instability in polymers: Since Q is the volumetric?
ASTM D3364 Flow Rates for Poly Vinyl Chloride
Summary of Test Method 4. At least twice a day check the ori? The instrument is now ready for the next test. Do not use the? How can we help you? NOTE 3—Occasionally, the values change throughout the run. This test method is used for quality-control tests on PVC compounds that have a wide range of melt viscosities.
Software for Series Systems. The quantity of material introduced into the barrel is 2. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility. Measurements are made at shear rates close to 1 s?
This weight is effective for all semirigid PVC and even some nonrigid compounds. However, as a one-point measure of flow relative to shear rate, its one drawback is that the same PVC melt flow values can be obtained for materials having different processibility; the chance of this happening is minimized, however, if the compounds are similar in composition.
Divide the difference by the average and multiply by D3364 Total load on piston Approximate pressure Charge Plugged ori? The principles of Contact Us View Accessories Catalog.
This may be due to variable lubricant conditions at the metal surfaces or chemical changes in the PVC compound. Subscribe to Our Newsletters. If charging time is greater than 1 min, clean out the instrument and repeat the procedure.
These changes are due to three types of measured instability in polymers:. The measured MFR value was found equal to 7. For PVC, N varies from 0.
ASTMD Standard Test Method for Poly(Vinyl ride) with Molecular Structural Implications_百度文库
Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phonefaxor service astm. Link to Active This link will always route to the current Active version of the standard. Users of this test method should apply the principles outlined in Practice E to generate data speci?
Check this box to receive pertinent commercial email from Instron focusing on products, upcoming events, and more! Current edition approved March 10, The following explanations of r and R Subscribe to Instron News! Dry off the cooled die with a cloth and inspect to see that the ori? Fluctuations up and down repeatedly during a run can indicate nonuniform mixing or a bad charging technique.
For each material, all the samples were prepared at one source, but the individual specimens were prepared at the laboratories which tested them.
It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.