Buy ASTM D Standard Test Method for Consolidated Undrained Triaxial Compression Test for Cohesive Soils from SAI Global. GeoTesting Express is a provider of Soil Testing Services – ASTM D, Standard Test Method for Consolidated Undrained Triaxial Compression Test for . Consolidated Undrained Triaxial Compression Test for Cohesive Soil.
|Published (Last):||1 February 2005|
|PDF File Size:||6.47 Mb|
|ePub File Size:||6.40 Mb|
|Price:||Free* [*Free Regsitration Required]|
A typical Standard triaxial system with analogue measurements includes: Generally, three specimens are tested at different effective consolidation stresses to define a strength envelope.
Active Risk Management
Standard triaxial configuration with built-in data acquisition can be used for performing additional tests such as CBR, Unconfined and CRS. Link to Active This link will always route to the current Active version of the standard. With this equipment it is possible to asym the consolidation stage of three triaxial specimens at the same time for CU and CD tests in anisotropic conditions.
Using the pore-water pressure measured during the test, the shear strength determined from this test method can be expressed in terms of effective stress.
ASTM D, Test equipment Controls
The load frame is built around a robust twin column A typical standard triaxial system with built-in acquisition measurement includes: It is scientifically undesirable to combine the use of two separate sets of inch-pound units within a single standard. Soil mechanics – Dynamic triaxial systems: Triaxial cells for advanced applications The cell essentially consists of a trasparent banded chamber to prevent excessive expansion during the test and to protect against explosive failure when used with compressed air systems.
TRITECH original high-performance load frames for triaxial tests, ideal solution for advanced and research laboratories that perform high quality tests at high productivity levels. Three or six simple thumbscrew are used to clamp the upper part of the cell to the base, which make assembly and disassembly a very quick and Reporting of test results in units other than SI shall not be regarded as nonconformance with this test method.
Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.
Maintenance Spares Technical trainings Warranty Academy.
asttm More than system configurations are available depending on type of test, sample size, pressure system. Soil mechanics – Triaxial Cells: Introduced by the company over 50 years ago, they have undergone continuous development and are the ideal solution for advanced and research laboratories that want to perform high It offer excellent reliability, accurate testing and lower maintenance requirements.
Data acquisition can be shared with other soil testing equipment. Installed on a PC communicating with the system over a fast Ethernet connection, the software can be used to configure the system scalibrate transducers, specify test parameters, set After the density has been determined, the unit weight is calculated in SI or inch-pound units, or both. Work Item s – proposed revisions of this standard. Historical Version s – view previous versions of standard.
The asmt of the cell ensure vertical alignement of the cell ram by clamping the Perspex wall separately from It is beyond the scope of this test method to consider significant digits used in analysis methods for engineering design.
Note 1—If the strength is required for the case where the soil is not consolidated during testing prior to shear, refer to Test Method D or Test Method D A typical standard triaxial system with external data acquisition system includes: In this system, the pound lbf represents a unit of force weightwhile the unit for mass is slugs.
Historical Version s – view previous versions of standard Work Item s – proposed revisions of this standard Translated Version s: Soil mechanics – Triaxial load frames: In this standard density is given only in SI units.
All the data acquisition and test management are made in manual mode Power supply is only required for air compressor and for triaxial load frame during asm stage. Soil mechanics – Static triaxial systems: The shear strength of a saturated soil in triaxial compression depends on the stresses applied, time of consolidation, strain rate, and the stress history experienced by the soil.
Specimens are isotropically consolidated and sheared in compression without drainage at a constant rate of axial deformation strain controlled.
This implicitly combines two separate systems of units; that is, the absolute system and the gravitational system. Standard triaxial configuration with external data acquisition can be used for performing additional test such as CBR, Unconfined and CRS, Permeability.
Standard triaxial system with built-in digital data acquisition Standard triaxial System with built-in data acquisition is the ideal compact solution for performing standard triaxial tests such as effective and total stress.
Soil mechanics – Consolidation benches: Data acquisition is included in the load frame; four channels are available for load, displacement, pore pressure and volume change.
The inch-pound units given in parentheses are mathematical conversions which are provided for information purposes only and are not considered aatm. Consolidation bench for triaxial cells The apparatus has been designed to reduce the testing time for triaxial tests, where only one compression machine is available. Users of this test method are cautioned that compliance with Practice D does not ensure reliable testing.
It is the responsibility of the user of this standard to establish appropriate xstm and health practices and determine the applicability of regulatory limitations prior to use.
Agencies which meet the criteria of Practice D are generally considered capable of competent testing.
EmS technology is environmentally friendly and clean to operate, requiring no compressed air or hydraulic oil.