EUROMAP 70 Electrical Interface between Injection Moulding Views. 6 years ago. Euromap, · Electrical, · Interface, · Injection, · Moulding. Euromap 2: Mould Fixing Dimension for Injection Moulding Machines. Specific information .. Mechanical properties, , Mechanical restraints, The electric control M2C is used for large machines. – highest safety standards ( as per EN /EN ) – standardised integration via EUROMAP 70 interface.
|Published (Last):||15 June 2004|
|PDF File Size:||1.37 Mb|
|ePub File Size:||6.21 Mb|
|Price:||Free* [*Free Regsitration Required]|
A permanent monitoring of the clamping condition, the temperature, and the position of euormap die by a supplied, separate control offers the maximum possible safety for automated processes. This penetrates only a few millimetres into the die base plate and will therefore have no impact on the die and the products. The fixation is made in an all around clamping groove by means of clamping claws. The electric control M2C is used for large machines.
All of the desired performance levels can be met. Figure 14 Magnetic clamping system for a vertical Arburg machine With double rotary table Clamping plate at the top and at the bottom.
In addition, all requirements of EN for injection moulding machines and EN for presses are met. The product range “M-TECS” stands for magnetic clamping technology, that means clamping technology of the highest level and offers the following key advantages for the user: Unless otherwise noted, the switch contacts are switching the reference potential plug contacts: Clamping and unclamping of several dies at the same time within a second.
Magnetic clamping system for a KM The mould halves are heated euromal the magnetic heating eruomap.
EUROMAP 70 – version 1.5
With the smallest movement of a die half, the machine will be stopped guaranteed safety for man and machine. A supplied separate control in combination with the press control provides the required safety for man and machine. Pin d2 18 ueromap 36V DC max. There are no limits set to the geometric shape of the magnetic plates.
A further supplier added v. Figure 13 Magnetic clamping systems euromaap an injection moulding machine of the company Krauss Maffei Closure force: The forces can be adapted upwards and downwards to the needs of the machine.
Size and geometric shape can be freely designed as requested by the customer. Functional principle and interface of the magnetic clamping system: M-TECS square poles for eyromap heavy machining Each magnetic plate can be individually adapted to the particular machine table. In addition recommendations are given for signal voltage and current levels.
Technical Recommendations | EUROMAP – European Plastics and Rubber Machinery
For easy and safe mould change, roller bars with spring packs are installed below the magnetic plate. The system consists of two electro-permanent magnetic plates, a control, a remote control, a complete set of cables and mounting takes often only a few hours.
Die or mould change on punches and presses within a few minutes as well as further processing advantages are created with Hilma magnetic clamping systems. Pin a2 and Table 2: The signals are conducted from the signal source to the respective pin. Plug on the injection moulding machine male.
The technology of the magnetic clamping plates is based on the principle of an electro-permanent magnet and is thus safe, even in case of a pressure failure. Rotary table with magnetic plate.
M-TECS function principle for horizontal design. Also very small moulds are safely 7. During the whole machining process, the control continuously monitors the parameters of the magnetic force, the position of the die die contact and the temperature.
Power is only required for about 2 eeuromap to magnetise clamp the system at the beginning. The magnetic clamping systems or clamping plates have been especially designed for injection moulding machines, rubber presses, die casting machines, mould carrier and presses for metal forming.
Plug on the injection moulding machine female. For the injection moulding machine see Figure 2 and the magnetic clamping system see Figure 1 the plug contacts should be capable of taking a minimum of V and 10 A. The contact making is either potential-free or related to a reference potential supplied to a contact of 770 plug mounted on the injection moulding machine or the magnetic clamping system see Tables 1 and 2.
Exact positioning on the machine table is ensured using 20H7 longitudinal and crosswise slots. Additional Eyromap, mounting holes, stops and special dimensions are not a problem to us.